- Product 270966
Shure MX393/O Low Profile Boundary Mic
- Write a Review
The Shure MX393 Low Profile Boundary Microphone includes a programmable membrane on/off switch, an on/off indicator LED, and a miniature, three pin c...Read More
The Shure MX393 Low Profile Boundary Microphone includes a programmable membrane on/off switch, an on/off indicator LED, and a miniature, three pin connector, and detachable 12 ft. (3.7 m) cable. Attractively designed with a low profile, professional appearance, the MX393 microphone feature a choice of interchangeable condenser cartridges. The MX393 is the high-quality solution for a range of applications, such as altars, boardrooms and distance learning centers. Comes with an easy to use paint mask for your custom-color installations.
Great sound reinforcement mic for presenters.
- Flat frequency response across the vocal range for uncolored sound
- Interchangeable cardioid, supercardioid, and omnidirectional cartridges that provide choices for applications
- Sleek, low-profile design for unobtrusive appearance
- Balanced transformerless output for increased immunity to
- noise over long cable runs
- Low susceptibility to electromagnetic hum and Radio Frequency Interference
- Programmable on/off switch and LED on/off indicator
Order today for low profile, good quality speech capture.
MX393/O Low Profile Boundary Mic
- Frequency Response: 50 to 17,000 Hz
- Polar Pattern: Omnidirectional
- Output Impedance: EIA Rated at 150 Ohms(180 Ohms actual)
- Sensitivity (at 1 kHz, open circuit voltage): —22.0 dBV/Pa (79.4 mV) 1 Pascal=94 dB SPL
- Maximum Sound Pressure Level (1 kHz at 1% Total Harmonic Distortion,
- 1 kohm load): 111.5 dB
- Signal to Noise Ratio (referenced at 94 dB SPL): 76.5 dB
- Equivalent Output Noise (A-weighted): 17.5 dB
- Dynamic Range: 94.0 dB
- Common Mode Rejection: 45 dB minimum, 10 Hz to 100 kHz
- Switch Attenuation: 50 dB minimum
- Preamplifier Output Clipping Level: —6 dBV (0.5 V)
- Polarity: Positive sound pressure on diaphragm produces positive voltage
- on pin 2 relative to pin 3 of output connector.
- Power Requirements: 11 to 52 Vdc phantom; 2.0 mA current consumption
- Environmental Requirements: Operating Temperature Range: —18 degrees C to 57 degrees C (0 degrees F to 135 degrees F); Relative Humidity: 0 to 95%
- Dimensions (W x D x H) 3" x 4.26 x .833 (76.2 x 108.3 x 21.16 mm)
Review Snapshot®by PowerReviews
Reviewed by 1 customer
Displaying review 1
Comments about Shure MX393/O Low Profile Boundary Mic:
I purchased this mic really out of curiosity. I wondered if it would pick up a drum set in the studio as a room mic. placed maybe 4-8 feet away from the kit. An ambient mic. I had read this HAD to be placed on a large flat surface to work. Not so Kemosabe'. I even held this upside down and spoke into it as a announcer does at a boxing match and it recorded just fine. I did perform a mic shootout test with this and a AKG 414. The standard! Both were very quiet. But it is like comparing oranges to apples. Different functions for different mics. I set them up about 2 feet away from me at the same height placing the shure on a music stand(for the flat surface) They were also about 24" from each other so they could easily record my voice at the same time. (Imagine reaching out your arms to hold two mics. that's the set-up). I ran both through a 2 channel tube mic preamp and a Drawmer 241 compressor then into a recorder. I spoke at a distance of 24" slightly turning my head toward each mic to get a front on signal. I then moved within 6 inches of each mic switching between the mics as I spoke continuously. This was for about a minute. The result was: (drumroll) The AKG 414 was a better mic! lol Seriously though I knew it would be BUT what the Shure mx393 is/was a little more detailed and not as much bottom end warmth. Wasn't as mid-rangy as a Sm57, and was very quiet. This mic would work great for a room mic to gain some ambience. Place it about 6 feet from a drum kit, tilt it slightly (the best angle is a 45 degree, place it at Tom or Cymbal height. you should get a really great "add-in" mixed signal. I am also going to try it inside the bass drum laid flat and see how it blends with my Audix d6. I will also use it as a 3rd mic on acoustic guitars, (once again, try it 3-5 feet from the cabinet and I might just hang it over a drum kit as an overhead, just to see. however I have a pair of Neumann KM184 i use, so that experiment won't last long I'm sure. I think these PZM mics might actually catch on a an extra mic. I will say the it edged out the AKG 414 in this dept. From a distance or more than 3 feet, there is definitely more information to use coming through the XM393. The signal from the 414 seemed to get too warm, lose highs and crispness the further away you get. But once again, that's not what the AKG414 is designed for. The Shure Xm393 was created to pick up sounds at a distance. Go ahead and try to get one used first. But get one, you'll find some really cool uses for it. Btw, I also have 4 Groove Tube mics, a Manley, Rode NTK, a Bock, Audio Technica 4050 and an onslaught of 58' and 57's with a bucket full of Octava, Golden Age projects and others. But this is still a cool little mic.