- Product 276530
Audio-Technica ATW-2110 Body Pack Wireless System with Instrument Cable
- Write a Review
Includes the Audio-Technica ATW-R2100 receiver, ATW-T210 UniPak transmitter, and GCW guitar input cable. Automatic frequency scanning--standard on al...Click To Read More About This Product
We're sorry-this item is unavailable.
Find a similar product below or contact our experts for a recommendation of great alternatives. Call us at 800-449-9128.Customers Also Viewed:
Clear sound and rock-solid performance.
Includes the Audio-Technica ATW-R2100 receiver, ATW-T210 UniPak transmitter, and GCW guitar input cable.
Automatic frequency scanning--standard on all 2000 Series wireless receivers--finds and sets the best available channel at the touch of a button. For those using multiple wireless systems simultaneously, the 2000 Series offers another ease-of-use standout: any of its 10 channels may be used together--eliminating confusing frequency groups and other frequency-coordination problems. The 2000 Series also features True Diversity operation, which selects the better signal from the two receiver sections to reduce dropouts; a Tone Lock tone squelch system that fights interference; a rugged metal half-rack receiver with soft-touch controls and LCD display featuring RF and AF metering; and balanced XLR and unbalanced 1/4" output jacks for use with a wide variety of audio gear. Includes rackmount kit and detachable UHF antennas. Ground-lift switch helps eliminate audible hum caused by ground loops between the sound system and receiver.
The included GCW Guitar Input Cable is a 1/4" phone plug to locking 4-pin connector for use between your instrument and the A-T UniPak bodypack wireless transmitter. 36" (0.9 m) cable.
Consumer Alert:Most users do not need a license to operate this wireless microphone system. Nevertheless, operating this microphone system without a license is subject to certain restrictions: the system may not cause harmful interference; it must operate at a low power level (not in excess of 50 milliwatts); and it has no protection from interference received from any other device. Purchasers should also be aware that the FCC is currently evaluating use of wireless microphone systems, and these rules are subject to change. For more information, call the FCC at 1-888-CALL-FCC (TTY: 1-888-TELL-FCC) or visit the FCCs wireless microphone website at: www.fcc.gov/cgb/wirelessmicrophones.
- Automatic frequency scanning
- All 10 user-switchable channels are compatible
- True Diversity operation selects the better signal from the two receiver sections
- Tone Lock tone squelch system
- Rugged metal half-rack receiver with soft-touch controls and LCD display featuring RF and AF metering
- Balanced XLR and unbalanced 1/4" output jacks
- Includes rackmount kit and detachable UHF antennas
- Ground-lift switch helps eliminate audible hum caused by ground loops between the sound system and receiver
Professional wireless system for a price that won't break the bank. Order today!
ATW-2110 Body Pack Wireless System with Instrument Cable
- OVERALL SYSTEM
Operating Frequency: 656.125 to 678.500 MHz
Number of Channels: 10 total
Frequency Stability: +/-0.005%, Phase Lock Loop frequency control
Modulation Mode: FM
Normal Deviation: +/-5 kHz
Operating Range: 300' typical
Operating Temperature Range: 41 F (5 C) to 113 F (45 C)
Frequency Response: 100 Hz to 15 kHz
Receiving System: Dual independent RF sections, automatic-switching diversity
Image Rejection: 55 dB nominal, 50 dB minimum
Signal-to-noise Ratio: >100 dB at 40 kHz deviation (A-weighted), maximum modulation 40 kHz
Total Harmonic Distortion: <1% (10 kHz deviation at 1 kHz)
Sensitivity: 20 dBV (S/N 60 dB at 5 kHz deviation, IEC-weighted)
Intermediate Frequency: 65.75 MHz, 10.7 MHz
Audio Output: Unbalanced: 25 mV (at 1 kHz, ±5 kHz deviation, 100k ohm load)
Balanced: 12.5 mV (at 1 kHz, ±5 kHz deviation, 100k ohm load)
Output Connectors: Unbalanced: 1/4" (6.3 mm) phone jack
Power Supply: 120V AC 60 Hz, or 12-18V DC, 350 mA, with external supply
Dimensions: 8.27" (210.0 mm) W x 1.73" (44.0 mm) H
x 6.39" (162.2 mm) D
Weight: 2.2 lbs (1.0 kgs)
Accessories Included: Two flexible UHF antennas, rackmount adapters, AC adapter
RF Power Output: 12 mW
Spurious Emissions: Under federal regulations
Input Connections: High impedance, low impedance, bias
Batteries: Two 1.5V AA alkaline (not included)
Current Consumption: 150 mA typical
Battery Life: Approximately 9 hours (depending on battery type and use pattern)
Dimensions: 2.60" (66.0 mm) W x 3.63" (92.3 mm) H x 0.89" (22.5 mm) D
Net Weight: 2.82 oz (80 g)
Reviewed by 1 customer
Displaying review 1
Comments about Audio-Technica ATW-2110 Body Pack Wireless System with Instrument Cable:
Great bang for your Buck! I was real hesitant on any wireless system other than Shure but I really didn?t want to break the bank for my freedom. The unit comes with a great mounting kit for racks and is easy to use. The ten channels search flawless with no feedback, or chirping like you get from cheaper models brands. I use this unit around several Shure systems and one other Audio-Technica ATW-2110 with no problems. The unit has clear response with no break up of your sound. I use it near my rig so distance is not a problem indoors or outdoors for me but I still tested it about 75 feet away and it was still as clear as a bell. Drawbacks; you need to change the channel inside the Body Pack Transmitter when you change the channel on the receiver and that requires the use of the provided plastic screwdriver (don?t loose it keep it in the slot in the body pack). It is more of a nuisance and not a real problem. The body pack cable tip only come in straight I am a Les Paul guy and like angled end but still no big problem. I recently purchased a ?Snap Jack? cable and replaced the ends with the Angled ?Snap Jack? tip. Now I can change guitars with ease and absolutely no popping. I run a JTM Marshall and I never need to power down my tube amp. Additional Plus: I use a Gator G-Bus-8 Power Supply to the 18V power required and I can use the wireless right on my pedal board and with no need to find an additional plug for the power supply. My pedal board is custom made and can support the receiver. Open my pedal board, plug in the Gator Power Supply and my pedals and receiver are ready to go.