- Product 481011
Crown Xs1200 Power Amplifier
- Write a Review
The Crown Xs1200 represents a new era in affordable, quality power amplification. In a uniform, rugged 2U rack mount chassis and incorporating the be...Click To Read More About This Product
We're sorry-this item is unavailable.
Find a similar product below or contact our experts for a recommendation of great alternatives. Call us at 800-449-9128.Customers Also Viewed:
Massive, reliable, compact power .
The Crown Xs1200 represents a new era in affordable, quality power amplification. In a uniform, rugged 2U rack mount chassis and incorporating the best of tried-and-true design principles and innovative features, the Xs1200 amp provides extensive protection and diagnostic capabilities, including output current limiting, microprocessor-controlled DC protection, circuit breaker, and special thermal protection for the unit's transformers.
- Housed in a rugged, all-steel 2U chassis
- Efficient forced-air fan prevents excessive thermal buildup
- XLR-1/4" combo inputs
- 3-pin Phoenix-style inputs
- Daisy-chain XLR outputs Touch-proof binding post outputs
- Speakon outputs
- Precision detented level controls
- Five LEDs to indicate clip for each channel, power, AC mains, temperature and fault conditions
- Microprocessor-controlled protection system
- 3-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications
Xs1200 Power Amplifier
- Power Output: 2-ohm Dual (per channel) 1,600W; 4-ohm Dual (per channel) 1,100W
; 8-ohm Dual (per channel) 650W; 4-ohm bridge 3,000W; 8-ohm bridge 2,300W
Sensitivity (volts RMS) for full rated power at 4 ohms: 1.4V
Frequency Response (at 1 watt): 22 Hz to 22 kHz: 1 dB.
Phase Response (degrees at 1 watt, 20 Hz to 20 kHz): +5, 18
Signal-to-Noise Ratio: A-weighted, below rated power: > 102 dB. 22Hz to 22kHz, below rated power: > 97 dB.
Total Harmonic Distortion (THD) at full bandwidth power, from 20 Hz to 20 kHz: 0.5%.
Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) from full rated output to 40 dB: < 1%.
Damping Factor (8 ohm) 10 Hz to 400 Hz: > 200.
Crosstalk (below rated power): (1 kHz, 20 kHz): >65 dB, >45 Db
Voltage Gain (at maximum level setting): 47.4:1 (33.5 dB)
Load Impedance: Safe with all types of loads. 2 to 8 ohms in Stereo, 4 to 8 ohms in Bridge Mono
AC Line Voltage and Frequency Configurations Available (10%): 120VAC/60 Hz and 230VAC/50 Hz.
Input Connectors: XLR-1/4" combo connectors: One per channel, 3-pin female XLR connector and TRS 1/4" phone jack accept balanced or unbalanced signals. 3-pin Phoenix-style connectors (2-channel models only): One per channel, accepts balanced or unbalanced signals.
Input Impedance (nominal) balanced, unbalanced: 20 k ohms, 10 k ohms.
Output Connectors:_Balanced XLR connectors (2-channel models only): One per channel, 3-pin male XLR connector in parallel with XLR-1/4" combo and Phoenix-style input connectors for daisy-chain operation. 5-Way binding post output connectors: One pair per channel; accept banana plugs, spade lugs or bare wire. 4-Pole Speakon output connector (2-channel models only): One connector per channel. Accepts a 4-pole Speakon connector.
DC Output Offset (shorted input): < 75 millivolts.
Output Signal: Stereo, unbalanced, two-channel
Ventilation: Flow-through ventilation from front to back
Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation.
Air Volume Requirements (per minute per unit): 80.15 ft (2.27 m)
EIA Standard 19-inch (48.3-cm) rack mount width (EIA RS-310-B), 3.5-inch (8.9-cm) height and 17.14-inch (43.5-cm) depth behind the mounting surface
Weight Net Weight: 28 lb 14 oz (13.1 kg), Shipping Weight: 34 lb (15.4 kg)
Reviewed by 3 customers
Displaying reviews 1-3
I purchased two units a few years ago when Crown introduce this line of amplifiers. Purchased two more recently. I DJ and run a midsize PA for local events. The Xs1200 offer more power and weigh less than the Mackie 1400i's I used previously. I use various JBL cabs from subs to monitors. They all work perfect with plenty headroom to spare. The amps paired with Mpro418 subs are knockouts. The last two Xs1200s purchased run at 15A, which is preferred vs 20A when the amps were introduced...I guess Crown got the message. The bang for the price is well worth it.
I was impressed with the Crown XS1200 to drive monitors. The daisy-chaining thru's on the back are a very nice touch, which makes wiring a rack easier. The 4 monitors we were using; all with the standard 12inch cones had a nice open, full sound but lacked a little punch. Probably due to the very low damping factor these amps have. It would be nice to see Crown increase this factor back upto the 1000+ range, similar to the old MA series.But all in all, a nice amp for the money.
I have had this amp for 2 years now and it is still running strong. It has a good amount of power and is right in the middle as far as weight goes (between an XTI and Peavey CS). There were 2 negatives off the bat but they were very small. One is that is very long and didn't fit into a normal skb type rack case. I had to get one special made. Might work ok in a long 18" amp case. The other is that the power cord needs an adapter cord to be plugged into a normal 3-prong outlet, so don't forget that cord. Other than that no complaints.