- 180388 000000000 180388000000000
Drawmer DS201 Dual Noise Gate
- Write a Review
The DS201 is a sophisticated dual channel noise gate incorporating a number of features pioneered by Drawmer, which are invaluable to the sound engin...Click To Read More About This Product
6-Month* financing available.
The DS201 is a sophisticated dual channel noise gate incorporating a number of features pioneered by Drawmer, which are invaluable to the sound engineer, and not found on conventional noise gates. These features and its "user friendliness" have made it the "industry standard" throughout the world.
Setting up noise gates can be tedious and unrewarding. For example, when attempting to separate a signal from unwanted noise or crosstalk that is relatively high in level, spurious triggering of the gate by unwanted components within the sound can be a serious problem. This can often be experienced in the studio when recording a drum kit. If a gate is used to clean up the snare drum sound it is quite likely that the nearby hi-hats will spill into the snare drum microphone and cause the gate to open. Increasing the threshold level may cure this problem, but then there is a very real danger that any quieter snare drum beats may not cause the gate to open at all and the performance can easily be ruined.
The DRAWMER solution to this problem is the inclusion of two variable filters, one high-pass and one low-pass, which act upon the side-chain keying circuitry. By setting the output switch to key listen the user can hear the action of the filters and adjust them to reject high frequency spillage from the hi-hats. This now enables the gate to only open on the lower frequencies present in the snare drum.
Drawmer pioneered the concept of frequency conscious gating, and the Drawmer DS201 was the first noise gate to include this feature.
The very fast attack of the DS201 means that it can open in a matter of micro seconds, thus preserving the natural attack of whatever sound is being gated and the comprehensive envelope controls mean that the gain can be changed at whatever rate best suits the material being processed. With vocals for example, a fairly fast attack is needed so as not to clip the leading consonants but a slower release time will prevent the end of words being clipped off and will also fade out any noise gradually rather than cutting it off abruptly. This latter point is very important as the human ear is far more sensitive to rapidly changing noise levels than to a constant low level noise.
Another important role played by the gate is in the reshaping of existing sounds. An example of this might involve a simple sampling delay line used to store a sound to be re-triggered later and added to a mix. A gate can be used to impart a slower attack or faster decay to the sound and careful setting of the decay envelope can effectively hide any noise present at the end of the sample. When using a sampler or drum machine the gate can be considered a triggered envelope shaper, and the wide range allowed by the envelope controls make the DS201 ideal for this application.
The unit can be switched to accept a key input, which allows the gate to be triggered externally. An example of this would be to use a snare drum signal to open the gate on a separate ambient microphone to create a natural alternative to gated reverb.
Each channel can be individually switched from Gating to Ducking for 'voice over' applications or the removal of 'clicks' and 'pops'.
- Variable high pass and low pass filters for "frequency conscious" gating
- Comprehensive envelope control, attack, hold, decay, and range
- Key input for external triggering
- "Key listen" facility
- Extremely fast attack time, to preserve the natural attack of the sound
- Balanced inputs and outputs
- Stereo linkable
- Can be used for "Gating" or "Ducking"
- High audio specification
- INPUT IMPEDANCE: 20Kohm
- MAXIMUM INPUT LEVEL: +17dBu
- OUTPUT IMPEDANCE: 50 Ohm (bal), 100 Ohm (unbal)
- MAXIMUM OUTPUT LEVEL: +17dBu
- BANDWIDTH: <23Hz to 31KHz -1dB
NOISE AT UNITY GAIN with Expander Off:
- Wideband 22Hz - 22KHz CCIR ARM IEC A Q-Pk CCIR
- AV -90dB -90dB -95dB -95dB -84dB
- RMS -88dB -93dB -93dB -95dB -
- DISTORTION: 100Hz 1KHz 10Khz
- < 0.025% < 0.025% <0.025%
POWER REQUIREMENTS: 115Volt or 230Volt at 50-60Hz, 9 Watts
- FUSE RATING: 32mA for 230Volt, 63mA for 115Volt, CONFORMING TO BS EN 60127-2:1991 SHEET III
- FUSE TYPE: 20mm x 5mm, Class 3 time delay, 250Volt at 50-60Hz, 9 Watts
- CASE SIZE: 482mm (w) x 44mm (h) x 200mm (d)
- WEIGHT: (incl packaging) 3.4 Kgs
Musician's Friend Gold Coverage
Gold Coverage goes above and beyond the manufacturer's warranty to protect your gear from unexpected breakdowns, accidental damage from handling and failures. This plan covers your product for one, two, three or up to five years from your date of purchase, costs just pennies per day and gives you a complete "no-worry" solution for protecting your investment.
Gold Coverage Includes:
- Unexpected and unintentional spills, drops and cracks
- Normal wear and tear
- Power surges
- Dust, internal heat and humidity
Other plan features include:
- For products over $200, No Lemon Policy applies. If it fails for the same defect 3 times, it is replaced on the 4th breakdown. (Does not apply to failures due to drops, spills, and cracks)
- For products under $200 experiencing the above failures, a Musician's Friend gift card will be issued for the full price of the product + tax.
- Shipping fees covered if required for repair or replacement
- Plans are transferable in the event merchandise is sold
- Plans are renewable on new gear
*Limitations and exclusions apply. See terms and conditions for program details
Term for New Gear begins on date of purchase but does not replace the store return policy or manufacturer coverage.