- Product 243035
E-mu PIPEline Wireless Transmitter and Receiver System
- Write a Review
The E-MU PIPEline wireless transmitter and receiver system frees you from the tyranny of audio cables without sacrificing audio quality. E-MU PIPElin...Click To Read More About This Product
We're sorry-this item is unavailable.
Find a similar product below or contact our experts for a recommendation of great alternatives. Call us at 800-449-9128.Customers Also Viewed:
3 independent stereo channels, 15m range, and non-compressed audio with a 48kHz sample rate.
The E-MU PIPEline wireless transmitter and receiver system frees you from the tyranny of audio cables without sacrificing audio quality. E-MU PIPEline works as a wireless transceiver for your guitar or keyboard, or as the basis of a wireless in-ear monitoring system for your band. Because latency is so critical in music performance, PIPEline has a minimal delay of only 5.5ms, so it won't interfere with the feel of your music.
With E-MU PIPEline connected to your musical instrument, you'll be able to move freely in a 15 meter range from the receiver. If your other band mates want to join the wireless revolution, they can, because PIPEline has 3 independent stereo channels. Each instrument stays completely independent with zero crosstalk.
Have you always wanted an in-ear monitoring system, but couldn't justify the high price? E-MU PIPEline is the perfect solution for low-cost in-ear monitoring. Because PIPEline has 3 channels, you can have 3 separate stereo monitor mixes, or 1 transmitter can send a group mix to multiple receivers.
PIPEline's Audio quality is superb with no-compression and a 48kHz sample rate (better than CD). Encryption key handshaking between transmitter and receiver eliminates the possibility of picking up other wireless sources.
Because E-MU PIPEline works with any audio device, you can wirelessly connect any of your other audio gear. For example, use PIPEline to connect your iPod or MP3 player”or computer”to your stereo system, or put remote speakers in another room of your house without the hassle of routing speaker wires!
Consumer Alert:Most users do not need a license to operate this wireless microphone system. Nevertheless, operating this microphone system without a license is subject to certain restrictions: the system may not cause harmful interference; it must operate at a low power level (not in excess of 50 milliwatts); and it has no protection from interference received from any other device. Purchasers should also be aware that the FCC is currently evaluating use of wireless microphone systems, and these rules are subject to change. For more information, call the FCC at 1-888-CALL-FCC (TTY: 1-888-TELL-FCC) or visit the FCCs wireless microphone website at: www.fcc.gov/cgb/wirelessmicrophones.
- Mobile wireless transmit or receive
- Each Pipeline can be configured as a transmitter or receiver
- Better than CD Quality Digital Audio
- 15M (49ft) range:
- Rechargeable battery Lasts up to 10 hours in receive mode and 6 hours in transmit mode
- Analog/Digital inputs or outputs
Connect to the PIPEline for affordable wireless freedom. Order today!
PIPEline Wireless Transmitter and Receiver System
- I/O Configuration
Two RCA Flexi-Jacks can be configured either as inputs or outputs
The two RCA Flexi-Jacks can also be configured either as analog or digital (S/PDIF 48kHz)
Audio Line In/Out ” 3.5mm (1/8") stereo jack
S/PDIF 48kHz or RCA Audio Line In/Out
Frequency Response: 20Hz-20kHz +/- 0.15dB
Signal-to-Noise Ratio: (SNR) 98dB (typical)
Latency: 5.5ms in Dedicated Pairing Mode, 10ms in Broadcast Mode
Battery Life: 5 to 8 hours (typical)
Charge Time: 3 hours (typical)
Supply Voltage: 5V
Operating RF range: 2400 - 2483.5MHz
Number of RF channels: 3
RF transmitter power output: 16 dBm (typical)
Minimum System Requirements
AC Power 100/240V
(2) PIPElines are required (transmitter & receiver) or
(1) LONGboard/SHORTboard (with built-in PIPEline transmitter) and (1) PIPEline
Reviewed by 1 customer
Displaying review 1
I misunderstood some directions (and they are counter intuitive): on the transmitter, the volume up/down buttons work backwards from what you would expect: the "-" button make it louder; the instructions say that those button on the transmitter are attenuation level; "+ increases the amount by which the signal is reduced. They should probably change that to make it clearer (that is, maybe "+" should make the signal louder ...).But with the attenuation on the transmsitter at minimum, and teh volume on the receiver at maximum, my headphones are plenty loud.The transmitter still clips sooner than I'd like, but I can get the volume I need. Others may want their in ears or headphones to be louder, so you should try before you buy, or at least use MF return policy.