Mackie HR824mk2 Studio Monitor (2010)
Mackie HR824mk2 Studio Monitor (2010)
Turn your studio's sweet spot into a full-on sweet zone.
The high-resolution Mackie HR824mk2 Active Studio Reference Monitor sounds as smooth as it looks. The rounded contours of the HR824mk2 monitor's Zero Edge Baffle minimize diffraction to give you a crystal clear audio image of your mix. The Mackie Optimized Waveguide delivers full, articulate mids, while the rear-firing, mass-loaded passive radiator ensures tight bass extension to 37Hz. Acoustic Space, low-frequency (LF) roll-off and high-frequency (HF) controls let you easily tailor the sound to suit your space and taste. And thanks to remarkably linear frequency response, Mackie HR824mk2 audio monitors ensure accurate mix translation. Combine all this with wide, even dispersion, and Mackie HR824mk2 monitors turn your studio's sweet spot into a full-on sweet zone.
High-resolution Active studio reference monitor
Ultra-linear frequency response for accurate mix translation
8.75" high-precision, low-distortion LF transducer
1" titanium dome, ferrofluid cooled tweeter
Optimized Waveguide for wide, even sweet zone
Twin FR Series amps - 150W for LF / 100W for HF
Cast aluminum Zero Edge Baffle minimizes diffraction
Full internal damping eliminates midrange artifacts
Passive radiator provides tight, articulate bass extension down to 35Hz
Acoustic Space, LF roll-off, and HF controls
Balanced XLR, TRS, and unbalanced RCA inputs
OmniMount ready for easy wall/ceiling placement
THX pm3 certified for surround sound applications
Order today and hear your mixes with a new level of accuracy.
HR824mk2 Studio Monitor (2010)
Acoustic Section Free-field Frequency Response: &plsumn;1.5dB, 37Hz to 20kHz Lower cutoff frequency: -3dB @ 35Hz Upper cutoff frequency: -3dB @ 22kHz Sound Pressure Level at 1 meter, -7.5dBu into balanced input: 100dB SPL @ 1m Maximum peak SPL per pair: 120dB SPL @ 1m Maximum short term SPL on axis, half space 80Hz to 2.5kHz: 111dB SPL @ 1m Residual noise (maximum gain, 600Ω source, 20Hz-20kHz bandwidth): < 8dB SPL @ 1m Rated Line Input Voltage and Power: (Power consumption): Standby mode: 8 watts Quiescent (idle): 18 watts Musical Program, Loud mix: 135 watts US: 120 VAC, 60Hz Rated Power (For UL-6500, CSA-E65-94, EN-60065): 150 watts Amplifier Section (Low-frequency power amplifier) Rated Power (at 1kHz with 1% THD): 150W Rated Load Impedance: 4 ohms Burst Power Output: 350W Rated THD (1W to -1dB of rated power): 0.1 % Slew Rate: 35V/µS Distortion (THD, SMPTE IMD, DIM 100): <0.035% Signal-to-Noise (20Hz-20kHz, unweighted, referenced to 150W into 4Ω): > 102dB Cooling: Convection Design: Class AB, Parametric Servo Feedback (High-frequency power amplifier) Rated Power(at 1kHz with 1% THD): 100W Rated Load Impedance: 6 ohms Rated THD (1W to -1dB of rated power): 0.1 % Burst Power Output: 210W Slew Rate: 35V/µS Distortion (THD, SMPTE IMD, DIM 100): < 0.035% Signal-to-Noise (20Hz-20kHz, unweighted, referenced to 40W into 8Ω): > 102dB Cooling: Convection Design: Monolithic IC, Conventional Class AB System Specifications Input Type: Balanced Differential (XLR and 1/4" TRS), Unbalanced (RCA) Input Impedance: 20kΩ Balanced, 10kΩ Unbalanced Input Protection: Rfi and Level Protected Maximum Input Level: +20dBu Low Frequency filter: -3dB @ 37Hz, 2nd-order transitional high-pass filter, -3dB @ 47Hz, 4th-order Chebyshev high-pass filter, -3dB @ 80Hz, 4th-order Butterworth high-pass filter HF Equalization: ±2dB @ 10kHz, shelving Acoustic Space: (A position) -4dB @ 50Hz, shelving, (B position) -2dB @ 50Hz, shelving, (C position) flat (Compressor) Independent high and low-frequency overload detection Enclosure Alignment: 6th Order Over Excursion Prevention: 2nd Order High-Pass filter Low Line Voltage Shut Down: 60% of Nominal Line Thermal Protection: Amplifier Shut-Down, Auto Reset Muting: 5 seconds at turn-on Driver Protection: Independent LF and HF Detection, Overall Compression Transducers Low-frequency driver: Diameter: 8.75 inches (170mm) Sensitivity (2.83V, 1m): 91dB SPL Nominal Impedance: 4Ω Voice Coil Diameter: 1.6" (40mm) Frame: Die-cast magnesium Magnet: Ferrite Fully shielded: Ferrite opposing magnet High-frequency driver: Sensitivity (2.83V, 1m): 91dB SPL Nominal Impedance: 6Ω Power Handling (Long Term/Program): 20/50 watts Frequency Range: 1.6kHz to 22kHz Diaphragm/Suspension: Titanium with polymer suspension Voice Coil Diameter: 1.0" (25.4mm) Magnet: Neodymium Bucking Magnet: Ferrite opposing magnet Passive Radiator: 6" x 9" (152mm x 228mm) mass-loaded elliptical flat piston with variable thickness filleted-edge rubber surround Crossover Type: Modified Linkwitz-Riley, 24dB/octave @ 1900Hz Enclosure Materials and Construction: 3⁄4" (19mm) thick MDF cabinet construction with internal bracing to add to cabinet stiffness Piano-black gloss finish Die-cast aluminum exponential wave guide for controlled, wide dispersion from high-frequency driver and Zero Edge Baffle to minimize diffraction around the cabinet edges Open cell adiabatic "foam fill" acoustical damping material absorbs internal reflections, preventing delayed sound coloration Flush-mount connector system allows monitor to be placed against a wall without need for connector clearance Physical Properties Height: 16.8"/42.5cm Width: 10.8"/27.3cm Depth Enclosure: 11.4"/29.0cm Depth Overall: 13.8"/35.1cm Weight: 34.6lb./15.7kg
You are changing the Ship-To country.
Our product catalog varies by country due to manufacturer
restrictions. If you change the Ship-To country, some or
all of the items in your cart may not ship to the